Expert Calibration since 1971
ISO/IEC 17025 accredited calibration
Contact callab@fischercc.com to request a calibration quotation or to obtain status on your calibration order.
|
PRODUCT
|
MEASURAND
|
FREQUENCY RANGE
|
|---|---|---|
| Current Probe | Transfer Impedance | 10 Hz to 4 Ghz |
| Bulk Current Injection Probe | Insertion Loss | 10 Hz to 4 Ghz |
| Probe Fixture |
VSWR Insertion Loss |
10 Hz to 4 Ghz 10 Hz to 4 Ghz |
| EM Injection Clamp | Insertion Loss | 10 Hz to 4 Ghz |
| 150 - 50 Ohm Adapter | Insertion Loss | 10 Hz to 4 Ghz |
| LISN |
Impedance Insertion Loss Phase Isolation |
1 kHz to 400 MHZ 1 kHz to 400 MHZ 1 kHz to 400 MHZ 1 kHz to 400 MHZ |
| CDN |
Impedance Coupling Factor Insertion Loss Voltage Division Factor |
9 kHz to 300 MHZ 9 kHz to 300 MHZ 9 kHz to 300 MHZ 9 kHz to 300 MHZ |
| TEM Cell |
VSWR Insertion Loss |
DC to 3 GHz DC to 3 GHz |
| F-CVP-1 |
Voltage Division Factor |
100 Hz to 100 MHZ |
| FCC-TG-115A/EFT |
Rise Time Pulse Width |
|
| Attenuator, Terminations & Cables |
Transmission Coefficient Reflection Coefficient |
9 kHz to 8.5 GHz 9 kHz to 8.5 GHz |
Clause 7.1.3 of ISO/IEC 17025:2017 states that there shall be a clear understanding of the decision rule used to determine an in-tolerance or out-of-tolerance condition. Fischer Custom Communications, Inc. offers two decision rules explained below.
An acceptance of a decision rule does not prohibit changing to a different decision rule.
ISO/IEC 17025:2017 accredited calibration decision rule selection
- Decision Rule 1: Measurement data is reported without a Pass or Fail (in/out of tolerance) determination. The measured value and the associated measurement uncertainty are provided. If “Pre” and/or “Post” condition is requested it will state “DATA ONLY”.
- Decision Rule 2: An “in-tolerance” or “out-of-tolerance” condition is determined by Simple Acceptance. The acceptance limit is the same as the tolerance limit, as defined in ILACG8:09/2019 Guidelines on Decision Rules and Statements of Conformity. When a measurement result for the device is declared “in-tolerance”, the measured value(s) will fall within the acceptance limits and the uncertainty of the measured value will be reported.
Please state on your RFQ and purchase order which rule is preferred. If there is an inherent standard such as CISPR 16-1-2, IEC 61000-4-6, ANSI 6.4, Mil Std 461, CISPR 25, RTCA DO1-60 please refer to it on your RFQ.
Click here to download ISO/IEC accredited calibration decision rule
Product
Current Probe
MEASURAND
Transfer Impedance
FREQUENCY RANGE
10 Hz to 4 Ghz
Product
Bulk Current Injection Probe
MEASURAND
Insertion Loss
FREQUENCY RANGE
10 Hz to 4 Ghz
Product
Probe Fixture
MEASURAND
VSWR
FREQUENCY RANGE
10 Hz to 4 Ghz
Product
Probe Fixture
MEASURAND
Insertion Loss
FREQUENCY RANGE
10 Hz to 4 Ghz
Product
EM Injection Clamp
MEASURAND
Insertion Loss
FREQUENCY RANGE
10 Hz to 4 Ghz
Product
150 - 50 Ohm Adapter
MEASURAND
Insertion Loss
FREQUENCY RANGE
10 Hz to 4 Ghz
Product
LISN
MEASURAND
Impedance
FREQUENCY RANGE
1 kHz to 400 MHZ
Product
LISN
MEASURAND
Insertion Loss
FREQUENCY RANGE
1 kHz to 400 MHZ
Product
LISN
MEASURAND
Phase
FREQUENCY RANGE
1 kHz to 400 MHZ
Product
LISN
MEASURAND
Isolation
FREQUENCY RANGE
1 kHz to 400 MHZ
Product
CDN
MEASURAND
Impedance
FREQUENCY RANGE
9 kHz to 300 MHZ
Product
CDN
MEASURAND
Coupling Factor
FREQUENCY RANGE
9 kHz to 300 MHZ
Product
CDN
MEASURAND
Insertion Loss
FREQUENCY RANGE
9 kHz to 300 MHZ
Product
CDN
MEASURAND
Voltage Division Factor
FREQUENCY RANGE
9 kHz to 300 MHZ
Product
TLISN
MEASURAND
Impedance
FREQUENCY RANGE
150 kHz to 30 MHZ
Product
TLISN
MEASURAND
Voltage Division Factor
FREQUENCY RANGE
150 kHz to 30 MHZ
Product
TLISN
MEASURAND
Phase
FREQUENCY RANGE
150 kHz to 30 MHZ
Product
TLISN
MEASURAND
Decoupling of Common Mode Distrubance
FREQUENCY RANGE
150 kHz to 30 MHZ
Product
TLISN
MEASURAND
LCL
FREQUENCY RANGE
150 kHz to 30 MHZ
Product
TEM Cell
MEASURAND
VSWR
FREQUENCY RANGE
DC to 3 GHz
Product
TEM Cell
MEASURAND
Insertion Loss
FREQUENCY RANGE
DC to 3 GHz
Product
F-CVP-1
MEASURAND
Voltage Division Factor
FREQUENCY RANGE
100 Hz to 100 MHZ
Product
FCC-TG-115A/EFT
MEASURAND
Rise Time
FREQUENCY RANGE
Product
FCC-TG-115A/EFT
MEASURAND
Pulse Width
FREQUENCY RANGE
Product
Attenuator, Terminations & Cables
MEASURAND
Transmission Coefficient
FREQUENCY RANGE
9 kHz to 8.5 GHz
Product
Attenuator, Terminations & Cables
MEASURAND
Reflection Coefficient
FREQUENCY RANGE
9 kHz to 8.5 GHz
